I love this Flying Heart Wall Hanging, along with the Gears Texture Sheet 6x6, from Gypsy Soul, and I've been holding off using it until I had a good idea for decorating it. Scroll to bottom to see close-ups.
I always lay my pieces out to see how they look, and move them around if I need to. This is the arrangement I think I will be sticking with but, of course, that could change. I never really know.
Faux Galvanized Metal Technique:
Step 1: Paint both sides of the chipboard backing pieces with black acrylic paint. Let paint dry.
Step 2: Dry brush a coat of silver metallic paint over the surface, leaving some of the black paint showing. Let paint dry.
Step 3: Brush a wash of silver metallic paint plus water over the surface again, leaving a smaller amount of the black paint showing. Let dry.
Step 4: Run chipboard pieces through die cutting/embossing machine with embossing folder.
Step 5: Lightly sand the embossed areas to enhance the design. Use a damp baby wipe to pick up a small amount of black paint and edge the pieces, as shown.
Gears Texture Sheet
Brush crackle paste over the Gears Texture Sheet 6x6 on one side and let air dry.
Turn over and brush crackle paste on each corner, again let paste air dry. These corners will hang off of the background piece when attached diagonally.
Brush coat of Yellow Oxide over gears sheet, then a coat of Quinacridone Gold. Use baby wipe to wipe away some of the excess gold, leaving a bit more of the yellow to show through. You will need to do this same process for the corners on the back of the sheet. Glue gears sheet to square background chipboard piece, as shown.
Large Heart and Wings
Add a thick layer of crackle paste to the heart and allow it to air dry.
Paint heart with Transparent Red Iron Oxide and let dry. Add a light coat of Interference Gold over heart and let dry.
Use a baby wipe to pick up a small amount of carbon black acrylic paint and wipe over surface of heart, letting the color go into the cracks. Wipe away excess before it dries. Add a tiny amount of Primary Magenta over the surface and let dry. Then add one more light coat of Interference Gold to bring back the shine.
Paint wings with silver metallic paint, then with 1-2 coats of Titan Buff. Sand some of the buff color off of the wings to reveal some of the silver.
Add a wash of Cobalt Teal Hue with water to add the blue tint. Next, dry brush Worn Penny paint over the wings with a stiff brush.
Apply a coat of clear crackle glaze over the wings and let air dry.
Use damp baby wipe to pick up Carbon Black antiquing cream and cover wings, let dry. Wipe away excess antiquing cream, which will bring out the cracks made from the crackle glaze.
Repeat the wings process for the words, as shown below.
Corrugated Chipboard Pieces
Paint corrugated chipboard pieces with a coat of white gesso first. Spread patches of crackle paste over both pieces randomly, as shown, and let air dry.
Paint both pieces with Bright Brass metallic paint, let dry.
Then add a coat of Rich Espresso metallic paint.
With a damp baby wipe, pick up a tiny amount of Carbon Black acrylic paint and hit the tops of the corrugations, as well as the edges.
Glue both pieces to backgrounds, as shown. Remember to leave some space for the large key at the top of the square piece, and be sure not to cover up the single hole that is centered on one edge of the rectangular piece. This hole will be at the bottom of the wall hanging.
Cover heart shape with clear glue and pour texture pebbles and texture sand over it. Set aside to dry.
Paint with a wash of Transparent Red Iron Oxide and let dry. Then add a coat of Quinacridone Burnt Orange to give it a really deep color. Let dry.
Pick up a small amount of the Champagne Ice metallic lustre and hit the high spots.
Paint both keys with white gesso, let dry. Then paint both with Worn Penny acrylic paint and let dry. Emboss keys with Stripes embossing folder. Pick up Burnished Brass Metallic Lustre with your finger and rub over high spots, then seal with Gloss varnish.
For added depth and dimension, I added the carbon black antiquing cream over the keys to age it. (See photo of finished project).
Paint crown with white gesso, then silver metallic paint, let dry. Use stiff brush to dry brush Rich Espresso over bottom section of crown, let dry. Glue diamond gems to the top of each point on crown.
Finish gluing all the pieces to the base, as shown. Add metal embellishments to the bottom half, as shown. Hang more metal pieces from the center hole at the bottom. After I put it all together, I realized that the red in the hearts was the only red on the piece, so I just added little splotches of Transparent Red Iron Oxide to the corrugated piece on the bottom section to bring it all together.
Here are a few closeups of the two sections.
GSL Flying Heart Wall Hanging
GSL Gears Texture Sheet 6x6
Teresa Collins Circle Décor 8.5x11 embossing folder
Teresa Collins Cut n Boss machine
Sizzix Stripes embossing folder (for keys)
Texture Pebbles (Brea Reese)
Texture Sand (Brea Reese)
DecoArt Media Fluid Acrylics
Carbon Black Antiquing Cream
Transparent Yellow Iron Oxide
Quinacridone Burnt Orange
Cobalt Teal Hue
Transparent Red Iron Oxide
DecoArt Dazzling Metallics
DecoArt Metallic Lustre
White Crackle Paste
Clear Crackle Glaze
Metal pieces (Tim Holtz Idea-ology)
I hope you enjoyed today's project, and I encourage you to stop by the Gypsy Soul Laser Cuts shop to see all of the fabulous laser cut chipboard available.
Thanks for stopping by, and have a super creative day!