Gypsy Soul Laser Cuts' Christmas Mini Folding House Shrine

Happy holidays to everyone!  I hope you are enjoying the winter weather, wherever you are!  Today, I am going to be using a couple of Gypsy Soul Laser Cuts' newest sets, the Little Folding House Shrine and the Tiny Christmas Shapes sets.  These are so cute and are sized just right to work together perfectly!

Outside with doors closed

Outside with doors open

Inside with doors opened

Make hinges by cutting two pieces of Tyvek to 2-1/2" x 3/4".  Paint both sides of the Tyvek with gold acrylic paint.  Paint both sides of the house with the gold acrylic paint.  One side (showing) only needs to be painted around the edges.  Set aside to dry.

Glue Tyvek "hinge" pieces to the three house pieces, as shown.  Leave enough space between pieces to allow the doors to open and close.  

Outside

Inside

This is a great time to use some of those paper scraps you've been saving.  These two pieces are from a Basic Grey Mistletoe & Pears paper pad.  

Run paper through Xyron 3" sticker maker.

Xyron 3" sticker maker

Cut paper just slightly smaller to fit each section, leaving a scant hint of gold edge.  Adhere to each panel. 

Inside

Outside

Apply triangle paper pieces to the roof top, as shown, on each side, using the opposing prints. 

Inside

Outside

Outside when closed in front

Add a strip of the gold Dresden border along the edge where the two papers meet, as shown.

Inside

Outside

Outside when closed in front

Cut two of the tiny scalloped shingles in half and paint with white acrylic paint or white gesso.  Let them dry, then glue to the top portion of the roof, as shown.

Outside when closed in front

Outside view on back

Fill in both sides of the roof top with the snow writer snow, as shown. 

Outside when closed on front

Paint each of the pieces with acrylic paint, as shown. 

Glue a small piece of mica to the back of the window frame.  Use the Snow Writer to add snow to the window frame and the green tree. (NOTE:  I added a wash of Burnt Umber acrylic paint to the window shutters to age them.)

I found a little white button in my stash, so I stamped "25" on it with black permanent ink, then ran a piece of red floss thorugh the button and tied it off. 

Glue it to the top portion of the roof on the outside of the house, as well as the painted chipboard pieces, as shown.

Inside

I cut a printed word "NOEL" from one of the papers in the pad and glued that to the roof portion of the outside of the house.  Glue remaining chipboard pieces, as shown.  (NOTE: I glued a tiny strip of chipboard beneath the shutters, close to the window, so that I could angle them up and outward from the house.  This is optional, of course).

Outside

I have included a few more close-ups of the painted chipboard pieces for you.

Supplies Used:

GSLTiny Shingles Sampler

GSL Little Folding House Shrine (contact store)

GSL Tiny Christmas Shapes (contact store)

GSL Gingerbread House Mini Tall (window &  shutters)

2 strips Tyvek (2-1/2" x 3/4")
DecoArt Glorious Gold Metallic paint
DecoArt Americana Lamp Black acrylic paint
DecoArt Media Fluid Acrylics
  Diarylide Yellow
  Hansa Yellow Light
  Primary Magenta
  Translucent White
  Cadmium Red Hue
  Burnt Umber
  Sap Green
DecoArt Snow Writer

Basic Grey Mistletoe & Pears paper pad 

Xyron 3" sticker maker
Gold German Dresden border
Liquitex white gesso
Mica Pieces
Alphabet/Numbers stamp set
Black archival ink pad
White button
Red floss


Thanks for stopping by, and have a very Merry Christmas!!!

Barbara