Halloween Home Decor - Witchful Thinking

Howl-o everyone, and welcome to my bewitching blog-o-ween post!  I love Halloween, and so I made this fun and funky wall hanging to celebrate the occasion.

I found this MDF sign in my local dollar store.  I did not care what was on it because I am going to alter and transform it to my own taste.  And I cannot think of a better way to do this than with Gina's Designs Lasercuts chipboard shapes.

Prepare the base by first sanding off the glittered areas, then base coat twice, if necessary, with black gesso.  Adhere strip of spiderweb paper to bottom section of base, as shown.

Spread graphite paste through shatter stencil on left and right side of base, as shown.  The graphite in the paste dries sparkly, which is a really cool effect for my spider webbing.

Mask boots with a piece of removable tape and paint socks with orange paint mixed with some white gesso.  This was not shiny enough for me, so I went over it with Orange Peel Silks.

Spread black modeling paste through bat stencil over socks only.

Spread clear crackle glaze over boots and allow to dry naturally.  To bring out the cracks, rub Titanium White Antiquing Cream over boots and wipe away excess with damp paper towel.

Add Rich Cobalt dauber to base and spritz with water to allow the color to run and blend over the background.  Set aside.

Paint chipboard pieces with white gesso to seal it.  Any pieces that may stick past the base will need to be gessoed on the back side as well.  I also cut two pieces from a scrap of corrugated cardboard to resemble shoe buckles (shown lower right below).

Paint chipboard pieces as follows:

Barbed Wire Deco Frame - Paynes Grey, dry brush with Metallic Silver

Witchful Thinking - Quinacridone Violet, Paynes Grey, Carbon Black, Burnt Sienna, Raw Sienna,  Titanium White

Witch - Carbon Black Paynes Grey, Green Gold, Burnt Sienna, Raw Sienna, Translucent White

Raven - Paynes Grey, Translucent White

Buckles - Diarylide Yellow, Metallic Gold, Burnt Umber Antiquing Cream

Begin adhering the pieces to the base.  Adhere the barbed wire deco frame first, then adhere the words in the center of the frame.  I glued slivers of chipboard behind the letters to raise them off of the base before adhering it.

Pop dots were used to raise the witch up for some added dimension.

The raven was adhered to the toe of the right boot.

And a close up of those batty socks!

Ginas Designs Supplies Used:
Barbed Wire Deco Frame Rectangle
Title Witchful Thinking
Witches
String Alongs - Gothic (Raven) 

Other Supplies used:
Dollar store Halloween sign
Spiderweb paper (Authentique Spellbound)
sandpaper
Corrugated cardboard scrap
Layering Stencils: THS014 Shattered, THS046 Batground
Graphite paste (Finnabair)
DecoArt Media Black Gesso
DecoArt Media White Gesso
DecoArt Media Cadmium Orange Hue
DecoArt Media Paynes Grey
DecoArt Media Metallic Silver
DecoArt Media Green Gold
DecoArt Media Burnt Sienna
DecoArt Media Raw Sienna
DecoArt Media Titanium White
DecoArt Media Translucent White
DecoArt Media Carbon Black
DecoArt Media DecoArt Media Quinacridone Violet
Diarylide Yellow
DecoArt Media Metallic Silver
DecoArt Media Metallic Gold
DecoArt Media Titanium White Antiquing Cream
DecoArt Media Burnt Umber Antiquing Cream
DecoArt Media Black Modeling Paste
DecoArt Media Clear Crackle Glaze
ColourArte Orange Peel Silks Acrylic Glaze
ColourArte Rich Cobalt Radiant Rains dauber
ColourArte Orange Peel Silks Acrylic Glaze

Thanks so much for stopping by, and be sure to check out all the great holiday shapes at Gina's online store.  

Have a wonderful and creative week, and a very Happy Halloween.  

Barbara